You are here

Article Text

Article menu

Download PDFPDF

XML
Workplace
Original article
Lung cancer incidence among Norwegian silicon carbide industry workers: associations with particulate exposure factors
  1. Merete Drevvatne Bugge1,
  2. Kristina Kjærheim2,
  3. Solveig Føreland1,3,
  4. Wijnand Eduard1,
  5. Helge Kjuus1
  1. 1National Institute of Occupational Health, Oslo, Norway
  2. 2Cancer Registry of Norway, Oslo, Norway
  3. 3Department of Public Health and General Practice, Norwegian University of Science and Technology, Trondheim, Norway
  1. Correspondence to Dr Merete Drevvatne Bugge, National Institute of Occupational Health, Pb. 8149 Dep, Oslo N-0033, Norway; mdb{at}stami.no

Abstract

Objectives An increased lung cancer risk associated with total dust exposure in the silicon carbide (SiC) industry has previously been reported. The aim of the present study was to examine the relative importance of specific exposure factors by using a comprehensive, historic job exposure matrix based on about 8000 measurements.

Methods Cumulative exposure to total and respirable dust, respirable quartz, cristobalite, and SiC particles and SiC fibres was assessed for 1687 long-term workers employed during 1913–2003 in the Norwegian SiC industry. Standardised incidence ratios for lung cancer, with follow-up during 1953–2008, were calculated stratified by cumulative exposure categories. Poisson regression analyses were performed using both categorised and log-transformed cumulative exposure variables.

Results The lung cancer incidence was about twofold increased at the highest level of exposure to each of the exposure factors (standardised incidence ratios 1.9–2.3 for all agents). Internal analyses showed associations between exposure level and lung cancer incidence for all investigated factors, but a significant trend only for total dust and cristobalite. In multivariate analyses, cristobalite showed the most consistent associations, followed by SiC fibres.

Conclusions The results indicated that crystalline silica in the form of cristobalite was the most important occupational exposure factor responsible for lung cancer excess in the Norwegian SiC industry. SiC fibres seemed to have an additional effect.

  • Epidemiology
  • job exposure matrix
  • cristobalite
  • inorganic fibres
  • cancer
  • mortality studies
  • dusts
  • fibres
  • respiratory
  • hygiene/occupational hygiene
  • exposure monitoring
  • exposure assessment
  • organic dusts
  • fungi/moulds
  • agriculture
  • retrospective exposure assessment
  • longitudinal studies
  • metals
  • asbestos

This is an open-access article distributed under the terms of the Creative Commons Attribution Non-commercial License, which permits use, distribution, and reproduction in any medium, provided the original work is properly cited, the use is non commercial and is otherwise in compliance with the license. See: http://creativecommons.org/licenses/by-nc/2.0/ and http://creativecommons.org/licenses/by-nc/2.0/legalcode.

https://doi.org/10.1136/oemed-2011-100623

Statistics from Altmetric.com

    Request Permissions

    If you wish to reuse any or all of this article please use the link below which will take you to the Copyright Clearance Center’s RightsLink service. You will be able to get a quick price and instant permission to reuse the content in many different ways.

    What this paper adds

    • Workers in the silicon carbide (SiC) industry have an increased incidence of lung cancer.

    • The specific causal factors of this increase have not previously been known.

    • The present study shows that exposures to cristobalite and SiC fibres seem to be the most important occupational risk factor.

    • Control of the dust exposure in the SiC industry, especially in the furnace hall, is essential.

    Previous studies have shown that workers in the silicon carbide (SiC) industry have an overall increased risk of lung cancer. In a Canadian study, the standardised mortality ratio of lung cancer was 1.7 (95% CI 1.1 to 2.5).1 Cancer incidence among Norwegian SiC workers is previously studied in two follow-ups, with end points 1996 and 2005, with standardised incidence ratios (SIR) of lung cancer 1.9 (95% CI 1.5 to 2.3) and 2.0 (95% CI 1.6 to 2.4),2 ,3 respectively. Exposure–response associations were found with exposure to total dust, but due to limited information about exposure to specific dust constituents further studies with more detailed job exposure information were recommended.1 ,3

    Several airborne exposure factors in the SiC production are known or suspected lung cancer risk factors. Quartz and cristobalite from occupational sources are classified as carcinogenic to humans (International Agency for Research on Cancer—class 1).4 In vivo and in vitro studies have indicated that SiC fibres have toxicological similarities to asbestos fibres, which are known lung carcinogens.5 On the other hand, the most abundant exposure factor in the SiC industry, isometric SiC particles, has not shown carcinogenic potential in in vivo or in vitro studies.6 ,7

    The aim of this study was to examine the relative importance of the investigated exposure factors, quartz, cristobalite, SiC particles and SiC fibres, with respect to lung cancer risk in the Norwegian SiC industry, by using a comprehensive, historic job exposure matrix (JEM).

    The study was approved by the Regional Committee for Medical Research Ethics South-East Norway and by the Norwegian Data Inspectorate.

    Materials and methods

    Study cohort

    The study cohort was based on a previously established cohort in the Norwegian SiC industry.2 ,3 It consisted of 1687 men, employed in 1942 and onwards, with ≥3 years employment in the Norwegian SiC industry between 1913 and 2003, and alive after 1 January 1953. The database comprised name, date of birth, the Norwegian unique 11-digit identification (ID)-number, plant affiliation, employment dates, job code(s) and smoking information. Information about smoking was collected once from the occupational health services at the plants, and the workers were classified as never-, ever-smoker or unknown. The cohort was linked with the Norwegian Cancer Registry to obtain cancer diagnoses and dates of diagnosis for the period 1 January 1953 to 31 December 2008, in addition to dates of death and emigration. Linkage was performed using the Norwegian unique 11-digit ID-number assigned to all Norwegian citizens alive in 1960 or born later. Before 1960, linkage was performed manually, using name and date of birth. After linkage, name and ID-number was replaced by a unique, random number. Follow-up started after 3 years of total employment, or 1 January 1953, if the 3 years' duration of employment was reached earlier. End of follow-up was date of lung cancer diagnosis, date of death or emigration, or 31 December 2008. The 1687 workers contributed 42 910 person-years of follow-up to the study.

    SiC production

    The production of SiC by the Acheson method8 was established in Norway in 1913. By this method, a mixture of quartz sand and petroleum coke is heated in open electric resistance furnaces by a graphite core. The heating process lasts approximately 48 h, during which the temperature in the core approaches 2500°C. Quartz will react with carbon and form SiC and carbon monoxide at temperatures above 1720°C. At the end of the heating process, SiC is found in the region closest to the core. Further away from the core partly reacted material is found, and in the periphery, where the temperature can reach 1000°C, no transformation takes place. SiC fibres are formed during the process9 and are accumulated in the intermediate region, where the partly reacted material is found.10 The unreacted and partly reacted material is removed from the crude before transport to the processing department where the SiC is crushed and sieved, impurities are removed, and the grains are classified into size fractions before packing. The petroleum coke contains impurities of sulphur, which is oxidised to sulphur dioxide during the furnace process, and traces of polycyclic aromatic hydrocarbons (PAH) in varying amounts. Cristobalite, a high temperature crystalline phase of silica, is formed during the furnace process, through transformation of quartz at around 1500°C.

    Exposure assessment and JEM

    Since 1967, personal total dust exposure has been measured with reference to specific job groups for routine control purposes and in connection with scientific exposure studies in the three Norwegian SiC plants. About 3300 measurements of total dust were available for reconstruction of the historical exposure levels. Based on the available total dust measurements covering the years 1967–2005, multiple linear regression models were developed for each department within each plant using a forward blockwise entry procedure. The following blocks were introduced into the model: (1) job group, (2) process related parameters, (3) 5-year periods and (4) a categorical variable accounting for the purpose of the measurement (research or compliance with occupational exposure limits). The exposure estimates were extrapolated backwards to periods without dust measurements by applying multipliers for estimated relative changes in exposure, based on information about process related changes and changes in working hours. Accordingly, estimates of total dust exposure were constructed for all job groups in the three plants and all years of production from 1913 to 2005.

    In order to estimate exposure to specific agents, a large comparative study was performed in 2002–2003,11 with around 700 parallel personal measurements of total dust and respirable dust, and total dust and fibres. The amounts of quartz, cristobalite and SiC dust in the respirable dust fraction were determined.11 This comparative study added approximately 5000 measurements to the exposure data. These measurements were used to develop linear mixed effect models estimating exposure to fibres, quartz, cristobalite, SiC dust and respirable dust from total dust exposure. The models were used to compute exposure estimates for the dust constituents from 1913 to 2005 based on the total dust estimates. The estimates were converted from geometric means to arithmetic means as described by Seixas et al12 and summarised in a JEM covering job groups in the three plants in the years 1913–2005. A few historical measurements of PAH existed, showing low exposure levels compared with current occupational exposure limits. PAH was therefore neither included in the measurement programme for the comparative measurement study nor in the subsequent modelling. Asbestos exposure was categorised as never-exposed/ever-exposed, and linked to job groups that had probable asbestos exposure in relevant time periods. No information about asbestos exposure outside the SiC industry was available. The development of the JEM is described in detail in Føreland et al (2012).13 A problem in the previous JEM3 was a high correlation between exposures to the different dust constituents, making differentiation of the effects from separate exposure factors difficult. In the present, revised JEM the correlation coefficients were moderate to low (rPearson≤0.72) except the correlation between total and respirable dust (rPearson=0.84).13 Some characteristics of the cohort and mean levels of the exposure factors are summarised in table 1.

    View this table:
    Table 1

    Mean years of employment with SD, and geometric mean (GM), geometric SD (GSD) and estimated arithmetic mean (AM) of annual intensity of exposure to specific exposure factors, by department and period of employment, for 1687 male long-term Norwegian silicon carbide industry workers employed during 1913–2003

    Cumulative exposure

    The information about employment periods and job codes for each individual in the cohort enabled a linkage with the JEM, thereby assigning individual mean exposures to total dust, respirable dust, respirable quartz, respirable cristobalite, respirable SiC particles and SiC fibres, for each year of employment in the SiC industry. Information on employment outside the SiC industry was not available. Individual cumulative exposure was summed up over all years of exposure. Cumulative exposure to each of the six exposure factors was categorised in three a priori defined groups (low, medium and high) ensuring equal numbers of person-years of follow-up in each category.

    Each job code was assigned a department affiliation: ‘Furnace department’, including mixing of raw materials, furnace process, and removal of non-reacted and partly reacted material; ‘Processing department’, including refining of the SiC into the specific grain sizes; ‘Maintenance department’, including mechanics, electricians and other maintenance personnel serving all departments; and ‘Other, low exposed personnel’, including laboratory workers, stock-house workers and office workers. Persons with employment in more than one department, or with unknown affiliation, were allocated to a ‘Mixed employment’ group. To this ‘Mixed employment’ group the furnace department contributed 2863 years of exposure, the processing department 2692 years of exposure, the maintenance department 2171 years and the group of ‘Other, low exposed’ jobs 1343 years of exposure.

    Statistical analyses

    SIRs were calculated as the ratio between observed and expected numbers of lung cancer cases. Expected numbers were based on the national cancer incidence rates for men, summed up in 5-year age and period groups. We performed SIR analyses of lung cancer stratified by department and by category of cumulative exposure to all exposure factors except asbestos, where a dichotomous exposure indicator was used. In order to account for the induction and latency time of lung cancer development, we also included analyses with 10 and 20 years lagging of exposure.14 In this study, 10 years lagging of exposure meant that the cumulative exposure level of a certain person-year was set to the cumulative exposure level of the same person 10 years earlier. We calculated 95% CIs for each risk estimate, assuming a Poisson distribution of the observed cases.

    Poisson regression analyses were performed for comparison of lung cancer risks between departments, using the ‘Other, low exposed’ category as the reference group. These analyses were adjusted for age (<55/55–74/≥75 years) only; for age and smoking (ever-, never-, unknown); and were also performed among ever-smokers only due to the low number of lung cancer cases among never-smokers (one case) and those with unknown smoking status (three cases). Exposure–response associations were studied using Poisson regression analyses of lung cancer related to categories of exposure, adjusted for age, among ever-smokers. Adjustment for period of diagnosis was not included in the final models, as inclusion of this variable did not change the estimates. Tests of trend were done by fitting a Poisson regression model for the linear effect of the exposure variables, assuming a constant increase in the log rate ratio per exposure category level.15 These analyses were also done with 10 and 20 years lagging of exposure. As an alternative to exposure lagging, Jahr's model16 (modified by Checkoway14) using time-weighted cumulative exposure was also applied. This model has been proposed for studying exposure–response associations with agents that are retained in active forms in the target tissues,14 and it was applied on quartz, cristobalite and fibre exposure, with and without a clearance factor assuming 10 years half-life of the investigated exposure factors.

    The relative importance of the specific exposure factors cristobalite, SiC, and SiC fibres was studied by constructing Poisson regression models including two or more exposure variables at a time. In order to limit the number of variables in the models, and to increase the stability of the analyses, we here used continuous exposure variables, which were justified by the monotonous increasing risk ratios of the categorised variables. Cumulative exposure to each exposure factor was log-transformed due to skewed distribution of the exposure. Correlation between exposure factors was investigated using Pearson's correlation coefficient (rPearson) between log-transformed cumulative exposures. Correlations between the cumulative exposure factors were moderately high (rPearson 0.51–0.77), except the correlation between quartz and cristobalite (rPearson 0.84), justifying analyses with SiC particles and fibres, and one of the crystalline silicas (cristobalite) simultaneously in the model. The relative effects of exposure factors were evaluated by studying how the effect estimate of one factor changed when a second factor was included in the model, and whether inclusion of a second factor contributed to a better fit of the model, according to the likelihood ratio test. These analyses were done among ever-smokers only. All p values are two-sided.

    All statistical analyses were performed using Stata V.11 (StataCorp LP).

    Results

    The lung cancer risk in this cohort of long-term SiC workers was increased compared with the general male population (SIR 1.6, 95% CI 1.3 to 2.1, 62 cases). The risk was highest among workers in the furnace department (SIR 2.3, 95% CI 1.5 to 3.5), and among those with employment in more than one department (mixed group; SIR 1.9, 95% CI 1.3 to 2.9). Both among processing and maintenance workers the SIRs were 1.4 (95% CI 0.7 to 2.7 and 0.7 to 2.6, respectively). The SIR in the low-exposed group was 0.6 (95% CI 0.2 to 1.9) (not shown in table). In the internal analyses, using the ‘Other, low exposed’ category as reference group, similar contrasts between the departments were observed (table 2). In analyses without adjustment for smoking, the incidence rate ratio (IRRs) were somewhat higher than in the smoking adjusted analyses, indicating a confounding effect of smoking on lung cancer incidence, seemingly strongest among furnace workers, who also had the highest ever-smoker percentage (76%). The department-specific IRRs among ever-smokers were almost similar to the smoking adjusted IRRs. The IRRs by smoking status gave high and unstable estimates due to the small reference group (only one lung cancer case among never-smokers) (table 2).

    View this table:
    Table 2

    Observed number of cases (Obs) and incidence rate ratio (IRR) with 95% CIs of lung cancer among 1687 male Norwegian long-term silicon carbide industry workers employed during 1913–2003 and followed up during 1953–2008, by department affiliation and adjusted for age and smoking status

    SIR analyses stratified by categories of cumulative exposure factors showed significantly increased risks with the highest level of all the four specific exposure factors (table 3). The risk estimates in the highest categories of cumulative exposure to all exposure factors increased when exposure was lagged 20 years. Internal analyses among ever-smokers, using the same cumulative exposure categories, gave increasing risks with increasing exposure to all exposure factors, and statistical significant tests of trend for cristobalite and total dust (table 4).

    View this table:
    Table 3

    Observed number of cases (Obs) and standardised incidence ratio (SIR), with 95% CIs of lung cancer among 1687 long-term Norwegian silicon carbide (SiC) industry workers employed during 1913–2003 and followed up during 1953–2008, by tertiles of cumulative exposure, and with exposure lagging 0 and 20 years

    View this table:
    Table 4

    Incidence rate ratios (IRR) and 95% CIs for lung cancer among 1166 ever-smoking Norwegian long-term silicon carbide (SiC) industry workers employed during 1913–2003 and followed up during 1953–2008, by tertiles of cumulative exposure, and with exposure lagging 0 and 20 years

    Lagging of exposure with 20 years gave significant tests of trend for all exposure factors except quartz (table 4). With 10 years lag of exposure, the results did not differ from the non-lagged analyses (not shown in table). The indicator of exposure to asbestos showed no association to lung cancer incidence (not shown in table). The ‘Jahr’ model with time-weighing of exposure did not give increasing risk estimates with increasing exposure levels (not shown in table). When a clearance factor assuming 10 year's half-life was added to the model,14 an exposure–response association was seen with cristobalite exposure, but no significant test of trend (not shown in table).

    In Poisson regression models using log-transformed cumulative exposure, the effect estimates of the other exposure factors were substantially reduced when cristobalite was added to the model (table 5). Adding cristobalite to a model already including SiC gave a significant likelihood ratio test, indicating a stronger effect from cristobalite. The effect estimate of cristobalite, on the other side, was somewhat reduced, and no longer significant when fibre was included in the model. Adding fibres in a model already including SiC reduced the effect estimate of SiC and gave a significant likelihood ratio test, but somewhat weaker than cristobalite. Quartz was not included in this model because of the high correlation with cristobalite (rPearson=0.84) introducing collinearity. With quartz in the model the effect estimates of both cristobalite and fibre increased considerably, whereas the effect estimate of quartz was reduced to about 0.5, indicating that the effect of both fibre and cristobalite was stronger that the effect of quartz.

    View this table:
    Table 5

    Incidence rate ratios (IRR) and 95% CIs for lung cancer related to log-transformed cumulative exposure to cristobalite, SiC fibres and SiC particles among 1166 male ever-smoking Norwegian long-term SiC industry workers employed during 1913–2003 and followed up during 1953–2008, adjusted for age and the other exposure factors

    Discussion

    We have, in this cohort of SiC workers, documented a 2–3 times increased risk of lung cancer associated with the highest level of cumulative exposure to all the investigated exposure factors. Applying a 20-year lag of exposure, significant exposure response trends were observed for all exposure factors except quartz. When two or more exposure factors were included in a Poisson model, lung cancer risk was most strongly associated with cristobalite exposure. An association with exposure to SiC fibres was also demonstrated, but this association was less marked than the cristobalite association. Exposure to quartz and SiC dust seemed to be of less importance.

    Crystalline silica from occupational sources is classified as carcinogenic to humans (Group 1) by the International Agency for Research on Cancer 1997.4 As pointed out by McDonald and Cherry,17 several of the studies showing an excess of lung cancer associated with crystalline silica exposure were conducted in manufacturing industries, entailing high temperature processes. Cristobalite is a high temperature crystalline silica polymorph. In vivo studies have shown that cristobalite produces a more rapidly developing pulmonary fibrosis18 ,19 and is cleared less effectively from the airways20 than quartz. Cristobalite exposure, however, is relatively infrequent in epidemiological studies, as cristobalite is a result of quartz heating, and thus limited to special industries. Some of the epidemiological studies giving the strongest evidence for an association between crystalline silica exposure and lung cancer are studies from the diatomaceous earth industry, where cristobalite is the most abundant crystalline silica polymorph.21 The highest exposed workers in our study had cumulative respirable cristobalite exposure estimates of 0.093–2.7 mg × years/m3, whereas the mean intensity of respirable cristobalite exposure in the furnace hall before 1960 was estimated to have been 0.074 mg/m3. Very few other studies have reported the levels of exposure to cristobalite. Rafnsson and Gunnarsdóttir reported respirable cristobalite exposure levels of 0.03–0.7 mg/m3 in the Icelandic diatomaceous earth industry, but did not report cumulative exposure levels.22 Rice et al reported mean cumulative levels of 2.2 mg × years/m3 respirable crystalline silica (maximum cumulative level 63 mg × years/m3) in the diatomaceous earth industry.23 Compared with these two studies, the historical cristobalite exposure levels estimated in our study was relatively low. Due to high correlation between cristobalite and quartz estimates, it was not possible in this study to separate the effect of quartz from the effect of cristobalite. However, it seems clear that cristobalite was the stronger factor of the two.

    Since SiC fibres (whiskers) were introduced as strengthening material in ceramics, several in vivo and in vitro studies have been performed in order to determine the toxicological importance of these fibres. This interest was amplified after SiC fibres were discovered as part of the working atmosphere in the furnace hall of the SiC producing industry.9 So far, studies have shown that SiC fibres have similarities with asbestos fibres, both with respect to direct cell toxicity5 ,24 and with respect to biopersistence.25 The results of the previous Norwegian SiC lung cancer study indicated that there could be an exposure–response association with SiC fibres, but the exposure data were too sparse to draw any firm conclusions.3 In the exposure assessment study which forms the basis of the JEM, SiC fibres were measured in parallel with total dust, giving job group specific estimates of SiC fibre exposure relative to total dust exposure.11 Although fibres had a stronger association with lung cancer than quartz and SiC, this effect was somewhat reduced when cristobalite was included in the multivariate model. However, the effect estimate (IRR) of SiC fibres after inclusion of cristobalite and SiC particles in a multivariate model was still 1.3, and we cannot from this study exclude an effect of SiC fibre exposure on lung cancer incidence.

    The exposure assessment study does not take into account the use of personal protective equipment (PPE) due to limited information about historical use of respirators. Such information was available only for 16% of the measurements before 2002. In the 2002/2003 investigation, 26% of the workers reported no use of PPE and 61% used PPE some of the time.11 Plant personnel were interviewed on historical use of PPE, and they informed that the use was infrequent in earlier years, and that the compliance is better now. Not adjusting for the use of respirators might thus lead to an overestimation of the inhaled dose, especially for the recent years. This again might lead to an underestimation of the exposure–response relation in the epidemiological analyses, but as all the lung cancer cases had their first employment before 1981, this underestimation is assumed to be minor.

    The information about smoking habits in the present study is limited to ever-smokers/never-smokers and unknown. In order to adjust for the well-known effect of smoking on lung cancer risk, we chose to perform the more advanced analyses on the subcohort of ever-smokers. By using the subcohort of ever-smokers in the IRR analyses at department level we got approximately the same risk estimates as when we adjusted for smoking. The advantage of limiting the analyses to ever-smokers was to obtain a better balance in the data, with less risk of collapse of the analyses due to few cases in some of the groups. A high correlation between intensity of smoking and degree of dust exposure could still give a possible bias, but this question could not be addressed with the information available in this study. Neither could the question of effect modification by smoking be addressed due to very few lung cancer cases in the never-smoker group.

    Potential exposure to other carcinogenic agents, such as asbestos and PAHs, should also be considered. We had in this study only qualitative information about asbestos exposure based on the plant personnel's knowledge about asbestos use in earlier times.13 Using an indicator of ever-exposure to asbestos, we found no evidence for an association with lung cancer incidence. The fact that the incidence of mesothelioma was at the level of the general population2 also indicates that asbestos exposure has not been of great relevance in this industry. Only a few measurements of PAHs have been performed in the Norwegian SiC industry, and the main part of these show low exposure levels, except in measurements related to crane operators prior to the introduction of fresh air ventilated crane cabins. Only one of the lung cancer cases in our study worked as a crane operator in this period. The mean of other measurements in the furnace hall was 1.0 μg/m3, compared with the Norwegian occupational exposure limit of 40 μg/m3. This, in addition to the fact that other cancers associated with PAH exposure, such as bladder cancer, was not increased in the SiC industry2 indicates that other factors than PAH were the more important carcinogenic agents.

    As lung cancer develops slowly, with 10–20 years induction and latency time, exposure lagging is frequently used in order to weight the assumed aetiologically most important exposures most heavily.14 Lagging of exposure with 10 and 20 years implies that each person-year of follow-up is assigned a cumulative level of exposure corresponding to the cumulative level 10 or 20 years earlier. The 10 years lagging gave no other results than the non-lagged analyses, whereas with 20 years lagging of exposure more significant exposure–response associations were seen, indicating a longer induction and latency period than 10 years. In order to study the effect of slow clearance of deposited particles and fibres from the lung, we also applied a model of time-weighted exposure. In this Jahr model, exposures are weighted relative to the number of years since exposure. These analyses did not show any exposure–response associations, in contrast to the analyses with 20 years lag. The results are difficult to interpret, but we might speculate that the Jahr model gives an overcorrection for the time factor in this context. The model was originally applied for latency consideration related to silicosis, and its relevance to carcinogenesis remains unclear.

    In Poisson regression analyses the question of overdispersion should be considered. We assume that there is no dependency between the lung cancer cases giving clusters. However, in order to evaluate the fit of the models, we performed the Poisson analyses (tables 2, 4 and 5) using the option of robust SE. These analyses gave only marginal adjustments of the CIs and no changes in the effect estimates or significance levels. We have therefore chosen to use the unadjusted numbers in the tables.

    Conclusion

    We have found a 2–3 times increased risk of lung cancer associated with the highest level of cumulative exposure to quartz, cristobalite, SiC particles and SiC fibres among workers in the Norwegian SiC industry compared with the general male population. Internal analyses using multivariate models indicated that cristobalite was the most important occupational risk factor, but exposure to SiC fibres also appeared to contribute to the increased lung cancer risk. Exposure to quartz and SiC particles was not seen to influence the lung cancer incidence.

    Acknowledgments

    The authors thank Jan Ivar Martinsen for his help with linking the Cancer Registry data and the JEM.

    References

    1. ↵
      1. Infante-Rivard C,
      2. Dufresne A,
      3. Armstrong B,
      4. et al
      . Cohort study of silicon carbide production workers. Am J Epidemiol 1994;140:1009–15.
      OpenUrlAbstract/FREE Full Text
    2. ↵
      1. Bugge MD,
      2. Kjuus H,
      3. Martinsen JI,
      4. et al
      . Cancer incidence among short- and long-term workers in the Norwegian silicon carbide industry. Scand J Work Environ Health 2010;36:71–9.
      OpenUrlPubMedWeb of Science
    3. ↵
      1. Romundstad P,
      2. Andersen A,
      3. Haldorsen T
      . Cancer incidence among workers in the Norwegian silicon carbide industry. Am J Epidemiol 2001;153:978–86.
      OpenUrlAbstract/FREE Full Text
    4. ↵
      International Agency for Research on Cancer. Silica, some silicates, coal dust and para-amid fibrils. IARC Monogr Eval Carcinog Risks Hum 1997;68:204–11.
      OpenUrl
    5. ↵
      1. Vaughan GL,
      2. Trently SA
      . The toxicity of silicon carbide whiskers, a review. J Environ Sci Health A Environ Sci Eng Toxic Hazard Subst Control 1996;31:2033–54.
      OpenUrl
    6. ↵
      1. Bruch J,
      2. Rehn B,
      3. Song H,
      4. et al
      . Toxicological investigations on silicon carbide. 1. Inhalation studies. Br J Ind Med 1993;50:797–806.
      OpenUrlPubMedWeb of Science
    7. ↵
      1. Bruch J,
      2. Rehn B,
      3. Song W,
      4. et al
      . Toxicological investigations on silicon carbide. 2. In vitro cell tests and long term injection tests. Br J Ind Med 1993;50:807–13.
      OpenUrlPubMedWeb of Science
    8. ↵
      1. Liethschmidt K
      . Silicon carbide. Ullmann's Encyclopedia of Industrial Chemistry. Vol. A 23. Weinheim, Germany: VCH Verlagsgesellshaft mbH, 1993:749–58.
      OpenUrlFREE Full Text
    9. ↵
      1. Bye E,
      2. Eduard W,
      3. Gjønnes J,
      4. et al
      . Occurrence of airborne silicon carbide fibers during industrial production of silicon carbide. Scand J Work Environ Health 1985;11:111–15.
      OpenUrlPubMedWeb of Science
    10. ↵
      1. Gunnæs AE,
      2. Olsen A,
      3. Skogstad A,
      4. et al
      . Morphology and structure of airborne beta-SiC fibres produced during the industrial production of non-fibrous silicon carbide. J Materials Sci 2005;40:6011–17.
      OpenUrlCrossRefWeb of Science
    11. ↵
      1. Føreland S,
      2. Bye E,
      3. Bakke B,
      4. et al
      . Exposure to fibres, crystalline silica, silicon carbide and sulphur dioxide in the norwegian silicon carbide industry. Ann Occup Hyg 2008;52:317–36.
      OpenUrlAbstract/FREE Full Text
    12. ↵
      1. Seixas NS,
      2. Robins TG,
      3. Moulton LH
      . The use of geometric and arithmetic mean exposures in occupational epidemiology. Am J Ind Med 1988;14:465–77.
      OpenUrlCrossRefPubMedWeb of Science
    13. ↵
      1. Føreland S,
      2. Bugge MD,
      3. Bakke B,
      4. et al
      . A novel strategy for retrospective exposure assessment in the Norwegian silicon carbide industry. J Occup Environ Hyg 2012;9:230–41.
      OpenUrlCrossRefPubMed
    14. ↵
      1. Checkoway H,
      2. Pearce N,
      3. Hickey JL,
      4. et al
      . Latency analysis in occupational epidemiology. Arch Environ Health 1990;45:95–100.
      OpenUrlCrossRefPubMedWeb of Science
    15. ↵
      1. Kirkwood BR,
      2. Sterne JAC
      . Essential Medical Statistics. 2nd edn. Malden, Massachusetts: Blackwell Science, 2006:249–62.
    16. ↵
      1. Jahr J
      . Dose-response basis for settling a quartz threshold limit value: a new, simple formula for calculating the “lifetime dose” of quartz. Arch Environ Health 1974;29:338–40.
      OpenUrlPubMedWeb of Science
    17. ↵
      1. McDonald C,
      2. Cherry N
      . Crystalline silica and lung cancer: the problem of conflicting evidence. Indoor Built Environ 1999;8:121–6.
      OpenUrlWeb of Science
    18. ↵
      1. King EJ,
      2. Mohanty GP,
      3. Harrison CV,
      4. et al
      . The action of different forms of pure silica on the lungs of rats. Br J Ind Med 1953;10:9–17.
      OpenUrlPubMedWeb of Science
    19. ↵
      1. Hemenway DR,
      2. Absher M,
      3. Landesman M,
      4. et al
      . Differential lung response following silicon dioxide polymorph aerosol exposure. In: Goldsmith DF, Winn DM, Shy CM, eds. Silica, Silicosis, and Cancer. Controversy in Occupational Medicine. New York, NY: Praeger, 1986:105–16.
    20. ↵
      1. Hemenway DR,
      2. Absher MP,
      3. Trombley L,
      4. et al
      . Comparative clearance of quartz and cristobalite from the lung. Am Ind Hyg Assoc J 1990;51:363–9.
      OpenUrlPubMedWeb of Science
    21. ↵
      1. Checkoway H,
      2. Heyer NJ,
      3. Demers PA,
      4. et al
      . Mortality among workers in the diatomaceous earth industry. Br J Ind Med 1993;50:586–97.
      OpenUrlPubMedWeb of Science
    22. ↵
      1. Rafnsson V,
      2. Gunnarsdóttir H
      . Lung cancer incidence among an Icelandic cohort exposed to diatomaceous earth and cristobalite. Scand J Work Environ Health 1997;23:187–92.
      OpenUrlPubMedWeb of Science
    23. ↵
      1. Rice FL,
      2. Park R,
      3. Stayner L,
      4. et al
      . Crystalline silica exposure and lung cancer mortality in diatomaceous earth industry workers: a quantitative risk assessment. Occup Environ Med 2001;58:38–45.
      OpenUrlAbstract/FREE Full Text
    24. ↵
      1. Stanton MF,
      2. Layard M,
      3. Tegeris A,
      4. et al
      . Relation of particle dimension to carcinogenicity in amphibole asbestoses and other fibrous minerals. J Natl Cancer Inst 1981;67:965–75.
      OpenUrlAbstract/FREE Full Text
    25. ↵
      1. Searl A,
      2. Buchanan D,
      3. Cullen RT,
      4. et al
      . Biopersistence and durability of nine mineral fibre types in rat lungs over 12 months. Ann Occup Hyg 1999;43:143–53.
      OpenUrlAbstract/FREE Full Text

    Footnotes

    • Funding The research has been supported with the aid of EXTRA funds from the Norwegian Foundation for Health and Rehabilitation, and with grants from the Norwegian Ministry of Labour.

    • Competing interests None declared.

    • Ethics approval The ethics approval was provided by Regional Committee for Medical Research Ethics South-East Norway, Oslo.

    • Provenance and peer review Not commissioned; externally peer reviewed.